Moersch Tanol Speed 200 Filmontwikkelaar - (2x100ml) + Glazen Flesjes

Moersch Tanol Speed 200 Filmontwikkelaar - (2x100ml) + Glazen Flesjes

€ 14,01
Prijs inclusief btw

Inclusief twee bruine glazen flesjes van 100ml en twee pipetten.

Compared to Tanol, Tanol Speed efficiently yields higher film speeds and can offer shorter developing times. The stain will render yellow-greenish and the fog density can be higher than usual for some black-and-white films. Tanol Speed is most suitable for black-and-white films with a nominal film speed between ISO 25 and 400. The rated nominal film speed can be achieved, and even exceeded, for the majority of film types.

Tanol Speed can only be used with a selective number of films that are listed by Wolfgang Moersch in the data sheet of the developer. Unlisted films cannot be used with this film developer, but keep in mind than only the common brands have been tested and you can experiment with some unusual black-and-white films if wanted.

In the data sheet, developing times are given between 20°C and 24°C. Wolfgang Moersch recommends using a temperature of 24°C. After pre-watering at the same temperature, the developer may drop by 1 °C at most at room temperature of 20°C, even for times longer than 10 minutes.

The standard dilution for Tanol Speed is 1+1+100, but other dilutions are given in the data sheet for higher film speeds.

For T-Max films, a dilution of 1+1+130 gives a sensitivity gain of 1°DIN. With Rollei Superpan and Ilford FP4, doubling the nominal speed is possible by extending the development time. Unlike conventional push development by underexposure and overdevelopment, the curve is not split up, but is arched up from the shadows to the mid tones, so there is a real gain in sensitivity, without the blocking of highlights. For some films, however, the gain of up to one stop is associated with an increase in fog density.

This developer is not suitable for higher-sensitivity films such as Delta 3200. For films with a tendency to high base fog (Kodak Tri-X, Rollei Retro and Infrared), Finol is the better choice.

Capacity: 2x100ml makes 20-26 liters of working solution - 60-90 films.

Film speed:
Using the recommended settings, if you make a reading with a colour-blind densitometer you get a silver density of 0.12logD or more for zone I. In the lower zones the total density (silver+stain) is only slightly higher than measured with a black and white densitometer. In the highlights the cumulative density is much higher. If you make your own evaluation with a black and white densitometer and you use VC paper, you may reach the nominal values of the zone system, but you must not exceed them. When using graded paper the curve (without the stain) has to be made flatter by shortening the development time.

The standard dilution is 1+1+100. To reach a higher film speed, use an alternative dilution from our data sheet.
On Tmax film with a dilution of 1+1+130 you gain 1°DIN in film speed. On Rollei Retro100 and Ilford FP4 you can double the nominal film speed by extending development times. In contrast to conventional push development by means of underexposure and overdevelopment, the curve is not steeper but bellied up from the shadows to the mid tones. This is a real gain in film speed without blocking the highlights. On some films this gain of up to one stop comes with an increase of the base fog.
This developer is not suitable for high speed films like Delta 3200. For films that have a tendency to develop a dense base fog (Tri-X, Rollei Retros and IR) Finol is the better choice.


1x Moersch Tanol Speed 200 Filmontwikkelaar - (2x100ml), 2x Glazen Fles 100ml, 2x Pipet
Type concentraat

Geen beoordelingen voor dit product momenteel.

Nieuwe account aanmaken

Reeds geregistreerd?
Log dan hier in Of Wachtwoord herstellen